Selur's Little Message Board
.mkv exporting problems - Printable Version

+- Selur's Little Message Board (https://forum.selur.net)
+-- Forum: Hybrid - Support (https://forum.selur.net/forum-1.html)
+--- Forum: Problems & Questions (https://forum.selur.net/forum-3.html)
+--- Thread: .mkv exporting problems (/thread-2306.html)

Pages: 1 2 3 4 5 6

RE: .mkv exporting problems - Selur - 25.03.2022

Quote: So it not possible for the content to stays as 4:2:2 when InterFrame convert it to 60fps?
Yes, Interframe only works with 4:2:0 content.
Quote: Do you have any filter suggestions to improve the quality?
tons of filters could remove noise, sharpen the image, etc. if you share a small clip of your source not some content you filtered, reencoded and YouTube reencoded too I can look at it and give some suggestions.

Cu Selur

RE: .mkv exporting problems - VHS_UK - 25.03.2022

(25.03.2022, 14:55)Selur Wrote:
Quote: So it not possible for the content to stays as 4:2:2 when InterFrame convert it to 60fps?
Yes, Interframe only works with 4:2:0 content.
Quote: Do you have any filter suggestions to improve the quality?
tons of filters could remove noise, sharpen the image, etc. if you share a small clip of your source not some content you filtered, reencoded and YouTube reencoded too I can look at it and give some suggestions.

Cu Selur

I'm not sure how on here since even a 15 second segment is over 200 mb.

RE: .mkv exporting problems - Selur - 25.03.2022

15sec are probably fine.
Upload it to google drive or similar and send me a link.

Cu Selur

RE: .mkv exporting problems - Selur - 25.03.2022

To get you started try the following:
  • start Hybrid
  • set "Filtering->Support" to Vapoursynth
  • enable "Filtering->Synth auto refresh"
  • enable "Filtering->Filter view"
  • enable "Filtering->(De-)Interlace/Telecine->Deinterlace/Telecine Settings->QTGMC Vapoursynth->Bob"
  • load your source
  • enable "Crop/Resize->Base->Picture Crop" ans set 'left: 12, top: 8, right: 18, bottom: 24' (to crop broken and fluctuating edges, partially caused by Stab)
  • enable "Filtering->Vapoursynth->DeGrain->TemporalDegrain" (to remove noise)
  • enable "Filtering->Vapoursynth->Spotless" and set "Temporal radius" to 3
  • enable "Filtering->Vapoursynth->DeHalo->FineDeHalo" and set 'Radius(x/y)' to '3/3'
  • enable "Filtering->Vapoursynth->Frame->Stabilize->Stab" and set 'Range' to '3' and 'Shift(max X/Y)' to '8/8'
  • opens the "Vapoursynth preview" to see the (deinterlaced&cropped) input on the left and the completly filtered content on the right.
then adjust the settings of those filters and may be also try different denoise and degrain filters instead of the ones I used.
You can also apply frame interpolation if you want, but I wonder why you even want to do that.
Another thing: when uploading to YouTube, it might make sense to increase the resolution.

Cu Selur

Ps.: And regarding capturing equipment the folks over at videohelp.com might have an idea what might be better suited.

RE: .mkv exporting problems - VHS_UK - 25.03.2022

Quote:Ps.: And regarding capturing equipment the folks over at videohelp.com might have an idea what might be better suited.


I'm not worried with equipment since I'm using a VC500 and a JVC S-VHS which is what I could get my hands on.  Thanks, I'll experiment with what you suggest.

Quote:set "Filtering->Support" to Vapoursynth

Does Vapoursynth do a better job with filters than Avisynth?

RE: .mkv exporting problems - Selur - 25.03.2022

Quote:Does Vapoursynth do a better job with filters than Avisynth?
Depends on the filters, usually Vapoursynth scales better on multi core systems.
Avisynth and Vapoursynth both have some filters the other doesn't.

If you have an NVIDIA graphics card which has 8GB (or more) RAM and is a 1XXX or newer card I could also send you a link to the torch-addon for Hybrid which allows to use a bunch if ml based filters.
Most older folks mainly stick with Avisynth because they are used to it.

Cu Selur

RE: .mkv exporting problems - VHS_UK - 25.03.2022

(25.03.2022, 17:00)Selur Wrote:
Quote:Does Vapoursynth do a better job with filters than Avisynth?
Depends on the filters, usually Vapoursynth scales better on multi core systems.
Avisynth and Vapoursynth both have some filters the other doesn't.

If you have an NVIDIA graphics card which has 8GB (or more) RAM and is a 1XXX or newer card I could also send you a link to the torch-addon for Hybrid which allows to use a bunch if ml based filters.
Most older folks mainly stick with Avisynth because they are used to it.

Cu Selur

Sorry, I only have a 6GB GTX 1660 Ti. My other spec is an i9 11900 and 32GB RAM.

RE: .mkv exporting problems - Selur - 25.03.2022

6GB should probably be fine, I'll upload a current torch addon and send you a link to it in ~1 1/2hrs via PM, so you can play with it.
You can then extract the addOn into the Hybrid/64bit folder which will overwrite the Vapoursynth folder and add a vsgan_models folder. Smile

Cu Selur

RE: .mkv exporting problems - VHS_UK - 25.03.2022

(25.03.2022, 17:53)Selur Wrote: 6GB should probably be fine, I'll upload a current torch addon and send you a link to it in ~1 1/2hrs via PM, so you can play with it.
You can then extract the addOn into the Hybrid/64bit folder which will overwrite the Vapoursynth folder and add a vsgan_models folder. Smile

Cu Selur

Thank you very much, going to be busy experimenting.

RE: .mkv exporting problems - VHS_UK - 26.03.2022

(25.03.2022, 20:49)VHS_UK Wrote:
(25.03.2022, 17:53)Selur Wrote: 6GB should probably be fine, I'll upload a current torch addon and send you a link to it in ~1 1/2hrs via PM, so you can play with it.
You can then extract the addOn into the Hybrid/64bit folder which will overwrite the Vapoursynth folder and add a vsgan_models folder. Smile

Cu Selur

Thank you very much, going to be busy experimenting.

Why does this keep appearing every time I start a job? Is to just notify me or an error? I get two of them before starting the job.