Crashed with exit status 0 - Printable Version +- Selur's Little Message Board (https://forum.selur.net) +-- Forum: Hybrid - Support (https://forum.selur.net/forum-1.html) +--- Forum: Problems & Questions (https://forum.selur.net/forum-3.html) +--- Thread: Crashed with exit status 0 (/thread-3480.html) |
Crashed with exit status 0 - Robbie303 - 29.11.2023 Hi Selur, I need your help again... I installed Hybrid on another PC, but there I got the error code: "Crashed with exit status 0" I have the HybridDebugOutput.txt file. Please let me know what info to give you. RE: Crashed with exit status 0 - Selur - 29.11.2023 Zip the DebugOutput and attach it. Also check whether the Vapoursynth Preview works, assuming you use Vapoursynth. Cu Selur RE: Crashed with exit status 0 - Robbie303 - 29.11.2023 Here is the rarred debug file attached. Where do I check if the vapour synth preview works? Is this at Filtering > VapourSynth > Misc > Preview ? (When I there select "Split Compare View" there is nothing different happening) At: Filtering > VapourSynth > Misc > Source, I have "UseDGDecNV when available" enabled.... RE: Crashed with exit status 0 - Selur - 29.11.2023 You open the Vapoursynth Preview,... (Filtering->Vapoursynth) RE: Crashed with exit status 0 - Selur - 29.11.2023 Using an unmapped file "\\server\e\Download .." will probably not work. => map that the server to a drive letter RE: Crashed with exit status 0 - Robbie303 - 29.11.2023 I moved to video file to my local drive, and also selected a local output directory as output for the video. I still get the same "Exit status 0" Doing the cropping of the file (auto Crop) works as normal, so, Hybrid is able to read the video file, also when the video is on the network. BTW: processing files from the network never showed any problems before. This Hybrid install is a clean install, I removed my previous Hybrid install and did a fresh install this morning. Sorry for being a bit slow with understanding.... But I still do not know how I should check whether the VapourSynth Preview is working..... When I go to: Filtering > VapourSynth > ..... Then there are a lot of options (tab-pages).... I see there is a tab-page: Misc > Preview... Should I do something there? I noticed at the right bottom: "Compare View" and under that a movieButton " VapourSynth Preview"... I enabled it and clicked on the preview... Hybrid was thinking, and then nothing happened. As I side note, I would like to mention something really important: Your support is amazing Selur RE: Crashed with exit status 0 - Selur - 29.11.2023 The debug output shows: y4m [error]: bad sequence header magic # Imports => Does the Vapoursynth Preview work? Cu Selur Ps.: "Vapoursynth Preview" button is in the lower right corner. RE: Crashed with exit status 0 - Robbie303 - 29.11.2023 See above, I added the info to my previous messages. Might be confusing, sorry about that... The input and output video paths are now local, but still get the same error. The VapourSynth preview is not working. I tried various video files, they all give the same error. RE: Crashed with exit status 0 - Selur - 29.11.2023 Quote:The VapourSynth preview is not working.Does it show an error? If yes, which error? If no, create a debug output where you try to open the Vapoursynth Preview. Cu Selur RE: Crashed with exit status 0 - Robbie303 - 29.11.2023 The VapourSynth Preview thinks for a few seconds and then stops. Nothing happens. Attached is the debugfile when I press the preview. |