25.10.2025, 03:47
I finally managed to get Hybrid , Vapoursynth and the addon compiled for ubuntu. It has been a challenge.
Hybrid starts but does throw one info box (see below) that when I close the UI opens and it appears to be working from a generic de-interlace test encode (24 min dvd source into mkv with x265 took about 7 minutes total) using just defaults for QTGMC (Vapoursynth) and x265 (audio is passthrough).
Upon adding some settings beyond the defaults from the test encode based on reading forum posts here and the information provided by hybrid when you mouse over settings the job (same input file as the test encode) started a little slower but over the last 4 hours has progressively gotten slower and slower.
system is pretty much idle with 1 vspipe process eating a CPU.
Job setting changes was to add bob to the deinterlace and then set framerate reduction to restore it to the source framerate
The startup info box is
I get this every time I start now. Before this fresh install of ubuntu and compile of everything, I had on another ubuntu install of the same version, Hybrid starting with no issues but it wasn't seeing vapoursynth via the addon so I wiped and started over.
Installed fresh OS, added user, and then started installing/compiling just the items needed to give me Intel GPU support in encoding, then Hybrid, Vapoursynth and the addon.
System information
OS: Ubuntu 24.04.3 LTS (I need this version because Alchemest GPU support is baked in as well as some other stuff)
CPU: AMD Ryzen 7 7800X3D (IGPU enabled)
GPU: Intel Arc A380
RAM: 32 GB
Hybrid Version 2025.07.27.1
I've got all the intel drivers/media stuff installed, ffmpeg has the intel QSV support, so I am unsure why it's not detected (Handbrake can see/use it).
I am working on re-running the job that hung up with debug turned on so I can add the output.
I will add it as soon as I can.
Thank you for this software as the test deinterlace was so much better than what I was getting from other tools.
Hybrid starts but does throw one info box (see below) that when I close the UI opens and it appears to be working from a generic de-interlace test encode (24 min dvd source into mkv with x265 took about 7 minutes total) using just defaults for QTGMC (Vapoursynth) and x265 (audio is passthrough).
Upon adding some settings beyond the defaults from the test encode based on reading forum posts here and the information provided by hybrid when you mouse over settings the job (same input file as the test encode) started a little slower but over the last 4 hours has progressively gotten slower and slower.
system is pretty much idle with 1 vspipe process eating a CPU.
Job setting changes was to add bob to the deinterlace and then set framerate reduction to restore it to the source framerate
The startup info box is
Quote:'lspci' didn't finish after 1 seconds -> aborting,... Restarting Hybrid might solve the problem,... The cause might also be some incompatibility with the tool and your system.
I get this every time I start now. Before this fresh install of ubuntu and compile of everything, I had on another ubuntu install of the same version, Hybrid starting with no issues but it wasn't seeing vapoursynth via the addon so I wiped and started over.
Installed fresh OS, added user, and then started installing/compiling just the items needed to give me Intel GPU support in encoding, then Hybrid, Vapoursynth and the addon.
System information
OS: Ubuntu 24.04.3 LTS (I need this version because Alchemest GPU support is baked in as well as some other stuff)
CPU: AMD Ryzen 7 7800X3D (IGPU enabled)
GPU: Intel Arc A380
RAM: 32 GB
Hybrid Version 2025.07.27.1
I've got all the intel drivers/media stuff installed, ffmpeg has the intel QSV support, so I am unsure why it's not detected (Handbrake can see/use it).
I am working on re-running the job that hung up with debug turned on so I can add the output.
I will add it as soon as I can.
Thank you for this software as the test deinterlace was so much better than what I was getting from other tools.