22.06.2026, 01:19
Debug seems to be working again when toggle on / off on the fly with "Hybrid_dev_2026.06.20-20172"
On a side note..
Regarding the other issue's i have reported.
ie: Speed Change not displaying the actual speed & DeblendS6 ..
One or both settings must have corrupted the output file..
The corruption wos:
A. During Video playback from time to time i saw weird huge chunks of square blocked graphic glitches.
And NO, it weren't macro blocks kind of blocks...
I've checked the source to see if it wos there aswel, but the source wos clean (perfect quality)
B. Sometimes weird loud sound poppups came out of my subwoofer, realy annoying
C. Process took over 2hours almost 3 hours
What I discovered, to my surprise, is:
That the cause was either a specific audio encoding setting.
Or the fact that I was forced to force the output fps via misc > overwrite output due to the fact Speed change in tab Speed Settings wos broken !!
Or both!
I'm not sure, I need to test this more..
What is strange is that the process took almost 3x longer than it should have, and the progress bar only went up to 50% of 100% to process a full job!
I also noticed that the remaining process time was displayed incorrectly! ie: 03:30:00 start to finish→ job completed at 01:00:00 left !!
From that, I could tell that something was not set up correctly and was causing all those problems!
Now, I think everything is set up perfectly.
The progress bar and remaining time are now displayed correctly.
Now, a full conversion to restore a complete 50-minute episode from SD to FHD (1080p) with ESRgan Upscales + DeblendS6 takes only 70 minutes instead of 150min 🥴👌🏽
EDIT: In the following image you'll see what sort of video distortion i have had using the old settings.
Once i've changed like 2 settings in the audio (pitch toggle=off & DownMix to 5.1).
And did use speed change in filtering tab again, instead of the forced speed change option in the misc tab ("overwrite output") because of the broken (wrong connected!) setting before in the regular place.
Lo & behold, all mentioned problems are gone now..
The Upscaled output plays as perfect as the original source now.
no more graphics glitches, and the pitch from the sound is like the original (no slowdown effect because of the fps difference)
But i STILL have to use 25FPS as an target for DeblendS6 for flawless and in sync video playback though ... When i put 24.000 value in deblendS6, again choppy video playback..
Example Video Corruption 👇🏽
![[Image: video-corruption.jpg]](https://i.postimg.cc/qqyf8mWZ/video-corruption.jpg)
cheers,
On a side note..
Regarding the other issue's i have reported.
ie: Speed Change not displaying the actual speed & DeblendS6 ..
One or both settings must have corrupted the output file..
The corruption wos:
A. During Video playback from time to time i saw weird huge chunks of square blocked graphic glitches.
And NO, it weren't macro blocks kind of blocks...
I've checked the source to see if it wos there aswel, but the source wos clean (perfect quality)
B. Sometimes weird loud sound poppups came out of my subwoofer, realy annoying
C. Process took over 2hours almost 3 hours
What I discovered, to my surprise, is:
That the cause was either a specific audio encoding setting.
Or the fact that I was forced to force the output fps via misc > overwrite output due to the fact Speed change in tab Speed Settings wos broken !!
Or both!
I'm not sure, I need to test this more..
What is strange is that the process took almost 3x longer than it should have, and the progress bar only went up to 50% of 100% to process a full job!
I also noticed that the remaining process time was displayed incorrectly! ie: 03:30:00 start to finish→ job completed at 01:00:00 left !!
From that, I could tell that something was not set up correctly and was causing all those problems!
Now, I think everything is set up perfectly.
The progress bar and remaining time are now displayed correctly.
Now, a full conversion to restore a complete 50-minute episode from SD to FHD (1080p) with ESRgan Upscales + DeblendS6 takes only 70 minutes instead of 150min 🥴👌🏽
EDIT: In the following image you'll see what sort of video distortion i have had using the old settings.
Once i've changed like 2 settings in the audio (pitch toggle=off & DownMix to 5.1).
And did use speed change in filtering tab again, instead of the forced speed change option in the misc tab ("overwrite output") because of the broken (wrong connected!) setting before in the regular place.
Lo & behold, all mentioned problems are gone now..
The Upscaled output plays as perfect as the original source now.
no more graphics glitches, and the pitch from the sound is like the original (no slowdown effect because of the fps difference)
But i STILL have to use 25FPS as an target for DeblendS6 for flawless and in sync video playback though ... When i put 24.000 value in deblendS6, again choppy video playback..
Example Video Corruption 👇🏽
cheers,