I've just installed on my Windows 10 PC and I'm getting errors when trying to process an MKV rip of a DVD file.
Quote:The procedure entry point_CxxFrameHandler4 could not be located in the dynamic link library C:\Program Files\Hybrid\64bit\Avisynth\avisynthPlugins\d3d9.dll
and:
Quote:AV1 is only allowed as raw or inside a mkv, mp4 or webm container!
Also I tried Vapoursynth, and when clicking preview I get "REMOVING RVRT" - the preview window now opens, but it is grey.
And now Hybrid isn't opening at all. It gets as far as "Updating tool versions" and then fails to open.
I uninstalled the dev version and installed Hybrid_2025.11.09.1_SETUP, but I'm still getting Exit1 crashes. What could have changed?
When switching versions make sure to uninstall the old version completly.
Quote: Also I tried Vapoursynth, and when clicking preview I get "REMOVING RVRT" - the preview window now opens, but it is grey.
Strange, there is only:
Code:
sendMessage(HCONSOLE, FOURSPACE + "REMOVING RVRT" );
That is some debug output I forgot to remove which shouldn't cause issues. (and only should be annoying => looking into it => Hybrid_dev_2026.02.28-181813 should be up in a few minutes)
Quote:AV1 is only allowed as raw or inside a mkv, mp4 or webm container!
As far as I know, this is correct. mov does not support av1.
Quote:The procedure entry point_CxxFrameHandler4 could not be located in the dynamic link library C:\Program Files\Hybrid\64bit\Avisynth\avisynthPlugins\d3d9.dll
No clue, might be some missing dependency.
Can you check the dll using DependencyWalker?
Cu Selur
I'll check the dependanccies tomorrow.
It's not an av1 file, it's an MKV rip of a PAL DVD.
Quote:It's not an av1 file, it's an MKV rip of a PAL DVD.
av1 is a video format,....
Argh, I see the problem:
Code:
2026.02.28 - 14:33:09_Windows 10 Version 22H2 (64bit)_2026.02.28.1 - level 9: ProResModel get->found no field 'codec'
2026.02.28 - 14:33:09_Windows 10 Version 22H2 (64bit)_2026.02.28.1 - level 9: AV1 is only allowed as raw or inside a mkv, mp4 or webm container!
=> Hybrid assumes av1 encoding is used, but you selected ProRes
Uploaded a new dev (Hybrid_dev_2026.02.28-195429) which should fix that.
(It was a typo, that was added when I added support for VCEEncC AV1 support.)
Cu Selur
Thanks. I guess I'll still have the missing dependency problem - not sure what's causing that after a clean install.
Which file do I need to open with Dependency Walker?
Attached is saved from opening Hybrid.
Quote:Which file do I need to open with Dependency Walker?
I would look at:
Code:
C:\Program Files\Hybrid\64bit\Avisynth\avisynthPlugins\d3d9.dll
try whether installing: Microsoft Visual C++ 2015–2022 Redistributable (x64) helps,..
"Hybrid.dwi-28.02.2026.zip " <- Hybrid starts, so this is useless,...
Cu Selur
Attached. This is from the Hybrid_2025.11.09.1_SETUP install.
Okay, so if I load your dwi here everything ahas a question mark at it, so that does not help me.
My guess atm is that either:
a. you are missing some runtime
b. you are missing direct X dependency or similar
since it works here and I have not changed anything around Avisynth++ for 2 years or so something must be missing on your system.
d3d is a Direct3D runtime file that is needed for FF3DFilterGPU.
Cu Selur
Ps.: going to bed now.
It's strange, Hybrid was working fine untill I updated to the latest dev version. I'm using the same PC and I haven't changed anything except Hybrid itself. Even going back to an older version of Hybrid now will not work, so perhaps the installation of the latet dev version removed some files?