The following warnings occurred: | |||||||||||||||
Warning [2] Undefined property: MyLanguage::$archive_pages - Line: 2 - File: printthread.php(287) : eval()'d code PHP 8.3.12-nmm1 (Linux)
|
hybrid target output resolution and resolution created through the script to not matc - Printable Version +- Selur's Little Message Board (https://forum.selur.net) +-- Forum: Hybrid - Support (https://forum.selur.net/forum-1.html) +--- Forum: Problems & Questions (https://forum.selur.net/forum-3.html) +--- Thread: hybrid target output resolution and resolution created through the script to not matc (/thread-2966.html) Pages:
1
2
|
hybrid target output resolution and resolution created through the script to not matc - Robbie303 - 08.12.2022 I get this error: -------- hybrid target output resolution and resolution created through the script to not match Target: 720x480 vs script: 708x480 -------- 01: the audio is extracted. 02: here either the video job crashes (resulting in the above error), or keeps on waiting forever. In Hybrid, I tried encoding with x264 and also with x265. Same error. Picture crop on/off, same error. At config-profiles, I did a reset all. Same error. I encoded the source file with Handbrake to x265 and then used that file for Hybrid. Same error. I have a 5 MByte source video file that reproduces the error, but the forum does not allow me to attach it... (also not as a rar file) Hybrid version 2022.11.28.1 RE: hybrid target output resolution and resolution created through the script to not matc - Selur - 08.12.2022 Quote:This log is only intended for user information. It should not be part of a bug/problem report!!-> Read the sticky, zip and share a debug output. Share details what you do. Ideally share the source. Cu Selur RE: hybrid target output resolution and resolution created through the script to not matc - Robbie303 - 08.12.2022 OK, I sent you a sample RE: hybrid target output resolution and resolution created through the script to not matc - Selur - 08.12.2022 Okay, but since you did not share a debug output, I don't know what you are doing in the script. When I load your source, it's detected as 720x480 with a 8x9 PAR. Trying to reproduce the issue I did the following:
MediaInfo reported the output as: Width : 720 Same when using DGDecNV as source filter in Vapoursynth. I attached the output that was generated. I also attached a version where I resized to square pixel. => Atm. I can't reproduce the issue here. No clue what you configured to get the issue you got. Cu Selur RE: hybrid target output resolution and resolution created through the script to not matc - Robbie303 - 08.12.2022 Thanks Selur, I found out that the problem started after I upgraded to the newest version. My previous Hybrid version was several months old, I do not know what was the previous version that I used. I have made a few hundredth of DVD encodes, so it was working OK, until I updated to the newest version (yesterday) I uninstalled Hybrid and removed all settings. Downloaded and installed Hybrid again, the installation went good, and settings were all cleared. I configured the output path, and turned on 'create debug file' But Hybrid never creates any debug file,,, strangely.... The video is now encoded correctly. No error. (but no bug file created) Then I do the following: turn on 'picture crop' and click on 'auto crop' Auto crop gives this result: Short clip - less than 100 seconds detected,... Analyzing the whole thing,... -> Crop result: 706:480:6:0, after 00:00:00.236hrs And now if I do an encode, I get the error again. RE: hybrid target output resolution and resolution created through the script to not matc - Selur - 08.12.2022 No debug output, so I try to reproduce this blind. I reset my Hybrid. Started it set the paths and some stuff under config->views, saved everything as defaults. Then I:
-> I'm looking into it. Cu Selur RE: hybrid target output resolution and resolution created through the script to not matc - Robbie303 - 08.12.2022 Great. And also have a look at the debug file generation... I never had 1 file generated until now. I did set the path and turned- on 'create debug file' RE: hybrid target output resolution and resolution created through the script to not matc - Selur - 08.12.2022 Okay, good and bad news. Good news: I found the issue and I think I fixed it. (also pressing auto crop a second time seems to fix it) Bad news: upgraded my cpu today, and now compiling crashes with some internal compiler error. -> Hopefully tomorrow after work I got enough time to fine the issue and fix it. Cu Selur RE: hybrid target output resolution and resolution created through the script to not matc - Robbie303 - 08.12.2022 CPU compiling crashes mnnnn,... nice If its only with your compiler and not with other CPU-intensive tasks, then tweak the compiler CPU options Computers are just like women: always trouble. RE: hybrid target output resolution and resolution created through the script to not matc - Selur - 08.12.2022 Okay, seems like it's the RAM timings of the new system. -> used totally conservative settings and got it working Will send you a link to a dev version for testing in a few minutes (uploading atm.) Cu Selur |